Alto-professional TMX120DFX Manual de usuario Pagina 6

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 52
  • Tabla de contenidos
  • SOLUCIÓN DE PROBLEMAS
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 5
6
30. AUX1-3 Controls - Adjusts the amount of the signal sent from the
ST SUB IN1-3 jacks to the AUX 1, 2 and 3 buses.
31. ST (stereo) Controls - Adjusts the amount of stereo signal sent
from the ST SUB IN1-3 jacks to the STEREO bus.
32. PFL (pre-fader listen) Switch - When this switch is engaged, the
signal at the point before the ST control knob is sent to the
PHONES jack.
33. POWER LED - The LED indicates when the power is switched
on.
34. PHONES Control - Controls the signal sent to the Headphone
Output.
35. LPF (MONO OUT) - This switch applies a low-pass filter to the
signal that is output from the STEREO bus. You can adjust the
frequency to the desired position by using a screwdriver to turn
the LPF Control.
36. ST (stereo) Control - Adjusts the level of the signal sent from the
2TR IN jacks to the STEREO bus.
37. PFL (Pre-fader listen) Switch - When this switch is engaged, the
signal input from the 2TR IN jacks is routed at the point before the
ST control to the PHONES jack.
38. AFL Switch - When this switch is on, the output
signal that passes through the ST OUT control fader
is sent to the PHONES jack.
39. PFL Switch - When this switch is engaged, the signal
at the point before the ST OUT control fader is sent to
the PHONE jack.
40. DFX RTN Fader - Adjusts the level of the return
signal which is sent from the built-in DSP to the
STEREO bus.
41. AUX1-3 Fader - The AUX1-3 faders adjust the final
level of the signal sent from the AUX1-3 bus to the
AUX SEND1-3 jacks.
42. MONO OUT Fader - Adjusts the final level of the
signal output from the STEREO bus to the MONO
OUT jack.
43. ST OUT Fader - The ST OUT fader adjusts the final
level of the signal sent from the STEREO bus to the
ST OUT jacks.
GRAPHIC EQ
44. EQ SWITCH - Engage this button to add the stereo graphic
EQ into the main mix output.
45. STEREO GRAPHIC EQ - Boosts or attenuates (+/-15dB) the
selected frequency at a preset bandwidth.
POWER AMP
46. POWER AMP. MODE Switch - Provides three modes: MAIN L / MAIN R;
AUX1/MONO; BRIDGE. Select any one of these modes to specify the signals to be
routed to the corresponding jacks according to the speaker connection on the rear
panel.
47. POWER AMP Switch - This switch is used to control the amplifier input signal.
DFX RTN AUX 1 AUX 2 AUX 3 MONO
OUT
STEREO
OUT
PFL
10
dB
-5
-10
-20
-25
-30
-40
-60
0
5
10
dB
-5
-10
-20
-25
-30
-40
-60
--
0
5
AFL AFL AFL AFL AFL
10
dB
-5
-10
-20
-25
-30
-40
-60
-
0
5
10
dB
-5
-10
-20
-25
-30
-40
-60
-
0
5
10
dB
-5
-10
-20
-25
-30
-40
-60
-
0
5
10
dB
-5
-10
-20
-25
-30
-40
-60
-
0
5
PFL
PFL
PFL
PFL
PFL
38
ST SUB IN 1
ST SUB IN 2
ST SUB IN 3
2TR IN
40
41
42
43
39
EQ OFF
EQ ON
-15
0
-10
-5
+10
+5
63
500250125
2K
1K
-15
0
-10
-5
+15
+10
+5
16K
8K4K
+15
44
45
AB
POWER AMP
OFF
ON
BRIDGE
AMP MODE
MAIN R
MONO
MAIN L
AUX 1
46
47
ST
PFL
AFL
1
2
3
ST SUB IN 1
30
31
32
ST
OFF ON
PFL
MONO OUT
PHONES
POWER
LPF(MONO OUT)
33
34
35
36
37
Vista de pagina 5
1 2 3 4 5 6 7 8 9 10 11 ... 51 52

Comentarios a estos manuales

Sin comentarios